Live-streamed games, recorded matches, and event data gathered in one place.
Kill Team Stream hosts quality live streaming of Kill Team content — tournaments throughout the year on Twitch, regular games streamed to the channel, and tournament data gathered so players can see what's happening in the scene. Powered by WARHAMMER.
Browse tournamentsOfferings
Tournaments
Multiple Kill Team tournaments hosted throughout the year, all live-streamed on our Twitch channel.
Videos
Streams are recorded and uploaded to YouTube alongside original video content we produce.
Event Data
Tournament packets from past events plus resources for upcoming Kill Team tournaments.
Site Directory
How to protect your painted Kill Team from travel damage
A painted Kill Team can represent many hours of careful assembly and brushwork, yet tournament travel treats it like any other fragile object. Models slide, bases twist, delicate weapons catch on foam, and a case can spend hours in a hot car. The aim is not to eliminate every scratch; it is to prevent avoidable impacts, abrasion and pressure while keeping the team presentation-ready for the table.
Good preparation starts before the first case is packed. Decide where each model will sit, stabilise vulnerable parts, allow paint and varnish to cure, and choose a carrying method suited to the route. That process is especially valuable for Australian events, where players may move between suburban clubrooms, major convention halls and cities such as Melbourne, Sydney, Brisbane and Adelaide.
Plan the journey before packing the models
Start by identifying the most awkward pieces rather than treating the whole team as one block. Bulky armour, extended arms, tall antennae and scenic bases need particular attention. Before packing a force built around bulky silhouettes, a practical Phobos armour tactics checklist on Kill Team Stream can help show which models are likely to be difficult to support. Photograph each operative from several angles and mark the vulnerable parts on the case plan.
Make a compact travel inventory of every model, weapon and separate base. A phone photo taken under bright light can reveal a loose component before it disappears into a crowded case. Keep rare or conversion models in individual labelled bags, but do not rely on thin plastic bags for impact protection. Those bags are useful for identifying parts; rigid foam and a close-fitting inner container should provide the actual restraint.
Next, match the transport method to the distance and the value of the team. A short drive to a local club night may need only a padded box and foam tray, while an interstate flight or a long rail journey benefits from a rigid case that can be kept under seat supervision. Check the current size and weight rules of the airline or rail operator, and treat the most valuable models as carry-on items where practical.
Seal the paint without flattening the detail
Paint needs a sacrificial surface, particularly on metal and resin models that will be handled repeatedly. If the team is already varnished, inspect it in good light for cracks, clouding or sticky areas before adding another coat. For an unvarnished finish, apply a compatible primer, base colour and several thin sealing layers rather than one heavy coat. Thin varnish follows sculpted detail better and is less likely to collect visibly at edges.
Let each product cure for the time recommended by its maker; a surface that feels dry may still be soft enough to mark. Acrylic paints generally handle travel well after proper curing, while enamels and oil details may need a longer settling period. Use clean, broad strokes from different angles and keep the model moving, because pooled varnish can form ridges around weapon edges or bases. A small test piece can confirm compatibility with an existing varnish.
Protect fine freehand markings from rubbing without burying them under tape or thick foam. Place soft tissue around loose scenic elements, secure them with a removable pinning material, and keep breakable 3D-printed weapons from carrying the load of the model. If a weapon will be posed away from the body, reinforce its joint before painting. The aim is a stable silhouette that can be slotted into foam without levering against the paint.
Build a case around the way models move
Closed-cell foam is useful because it does not shed fibres and can be cut into snug channels. Each base should sit in its own recess, with support beneath the feet and around the lower torso rather than around an arm or weapon. The model should not rock when the case is tilted. Avoid cutting a slot so tight that insertion presses against a base edge; persistent pressure can leave a pale ring or knock varnish loose.
Use layers of protection: a foam-lined inner box inside a rigid outer case, or foam trays inside a flight case. A separate lid prevents pieces from striking the base of the container when the case is set down. For a plastic tub or familiar Australian servo-lid option, make a fitted foam insert rather than letting miniatures slide loose. Label every removable tray so a rushed unpacking process follows the correct order.
Check that faction bases remain attached and undamaged, and pack any required alternative bases separately. Large scenery pieces deserve their own padded compartment, while loose weapons should be held in the hand or fixed safely to the model if the rules permit. Do not glue a removable part permanently unless the rules require it. A clear case layout also makes insurance photographs and post-event inspections far easier.
Account for Australian heat, distances and customs
Australian conditions deserve a specific plan. In summer, a case left in a parked car can quickly become hot enough to soften pressure-sensitive foam, while direct sunlight through windows can fade colours over repeated journeys. Keep the case out of the boot and out of visible glass. When moving from an air-conditioned venue into humid weather, leave the closed case indoors for a while so condensation forms on the outside rather than on the models.
Long domestic distances make case weight and access important. Interstate flights and rail trips between Melbourne, Sydney, Brisbane and Adelaide can involve several transfers, and checked baggage is the least controlled part of the route. Use a sturdy handle, a shoulder strap and a dry exterior cover. The Australian hobby market offers flight cases, foam sheet and purpose-built miniature storage through specialist retailers, local Games Workshop stores and independent model shops; a club case can also be shared among regular travellers.
For overseas tournaments, customs and biosecurity checks belong in the planning stage. Australian Customs restricts untreated timber and plant material, while loose soil, bark or vegetation on scenic bases may attract attention. Synthetic, soil-free basing reduces this risk, but existing scenery should be checked before the models travel, since dismantling it could damage the paint. Confirm the current rules for the destination and Australian departures rather than assuming a sealed case grants automatic clearance.
Inspect, handle and recover at the event
Inspect the team as soon as it reaches the venue, before fatigue makes details easy to miss. Open the case over a clear table, compare the contents with the travel inventory and photograph any damage. Keep the case closed between rounds so dust cannot settle on unfinished repairs. Before play, check each base, weapon and arm under local light; movement during a game can turn a hairline crack around a joint into a detached component.
Carry models by the base whenever possible, never by a weapon, antenna or sculpted hand. During deployment, keep the case below table height and place each operative into a foam recess until its position is settled. Bring only the colours, metallic shades, primer, brush, matte varnish and adhesive needed for a small repair, plus tissue, a microfibre cloth and a paper record of the original paint scheme. Test a primer or metallic patch before touching a visible surface.
After the final round, unpack in the reverse of the packing order and inspect under angled light. Clean loose dust with a soft brush, isolate damaged models so fresh paint cannot rub against another piece, and allow any repair to cure before returning the model to a closed foam slot. Repack the empty recesses before leaving the venue, since a missing tray is often the first sign that something has shifted. A disciplined case and a careful handover can return the same display-ready team home without sacrificing its finish.